Free bearing checker for SMEs with flood problem

admin — Fri, 09 Dec 2011 07:18:43 +0000

Accoring to flooding situation in Thailand, we are providing free service for bearing checker for all machines such as motor, gear, pump etc. for 15 measurement points within 3 months. Please contact us at direct line 02 971 8086 for appointment!

New! MHC-Sigma

admin — Fri, 07 Jan 2011 15:41:52 +0000

MHC-Sigma is an ultra smart sensor which has a capability which goes far beyond anything else we are currently aware of.

It requires 24V DC and its non-volatile settings are set-up from your PC via the SI/RT/C interface and the dual channel Sigma Interface Unit.

It rejects signals associated with machine start-up and slow-down.

It processes segments of signal as short as 500m seconds, yet still produces readings of Distress® and dB level.

It has a built-in alarm function.

It can give trendable outputs

It even has an internal 384 day FIFO trend history.

It can be used with intermittant revolution machineries that runs as start and stop such as crane, lift or even conveyor that runs on demand.

Maintenance Innotech 2010

admin — Sun, 28 Nov 2010 16:57:18 +0000

Maintenance Innotech 2010 is the exhibition for best practice and innovative instruments for condition monitoring. It is organised by SCG at National Science Park of Thailand on 26th November 2010. Acoutomatic Solution who is leader in Bearing Checker as for Condition Monitoring using Acoustic Emission technique (Holroyd Instruments, UK) also participate as an exhibitor. We have an invited keynote speaker Mr. Alastair Gregg who is an expert in Condition Monitoring using AE technique to present the topic of ‘New Innovation in simple to use condition monitoring’ . In addition, we also have our invited partners from AE malaysia Dr. Yang Soo Siang and Mr. Song who are representative from Malaysia to participate in this very event.

Our exclusive appointed re-seller in Malaysia

admin — Wed, 28 Apr 2010 09:52:51 +0000

AE Engineering SDN BHD (906241-V) is appointed as exclusive re-seller within Malaysia for the sale of Holroyd Instruments products.

Address: ACOUSTOMATIC ENGINEERING SDN BHD (906241-V),

TB14899, TAMAN JAMBU, BATU 3, JALAN SIN ON, 91000 TAWAU, SABAH, MALAYSIA.

TEL: + 6 089 777736

FAX: + 6 089 767739

Bearing acoustic emission noise

admin — Thu, 16 Apr 2009 04:52:07 +0000

This article is to present the use of Acoustic Emission (AE) noise emitted from bearing before and after lack of lubricant conditions. In general, AE is the mechanical wave generated when the material is subjected under stress. The release of mechanical wave or so called strained energy is of frequency around 100 kHz which can be used for bearing health indication. The use of AE for bearing or rotating machines checker can be very early to catch the machine fault condition for example, lack of lubrication, contamination, defect, wear, debris, rolling element, cage, inner-race or outer race defect. Therefore, Holroyd Instruments (UK), an expert in condition monitoring products, currently lauched state-of-the-art simple to use but really works bearing health checker for all kind of industry.

Bearing Checker

admin — Tue, 03 Feb 2009 01:00:22 +0000

Machine Health Checker (MHC) has wide ranges of products. Its function is to give the accurate measurement of rolling element bearing, journal bearing, gearbox, motor. The MHC products can take reading from machine straight away without any prior knowledge of bearing information. It only takes 15 seconds to get results wether the machine status is OK! or NOT! However, with the higher specification model such as MHC Memo Pro can also provide spectrum analysis of bearing defect frequency. Another emphasis can be made that with acoustic emission technology the MHC can give accurate yet reliable results for slow speed rotating machinery (down to 0.25 rpm).

Tank Floor Monitoring

admin — Mon, 02 Feb 2009 16:52:11 +0000

Tank Floor Monitoring (Above ground storage tank floor)

No need to empty tank
Risk-based inspection plan
Preventing environmental losses
Cost reduction

Tank bottom (or floor) plate inspection using Acoustic Emission technique is a very useful inspection method in petrochemical, oil&gas industries. This is because the side walls and roof can be conveniently inspected with conventional nondestructive testing methods and releases are readily detectable. Tank floors are therefore less accessible and evidence of release remains largely hidden from view until the extent of the release is large. In-service degradation of tank bottoms is a result of internal, under-floor corrsion activities, potential leaks, over-stress, and deformation.

Services

admin — Tue, 02 Dec 2008 03:05:45 +0000

We are providing the services for bearing and gearbox inspection using acoustic emission technology. With the total inspection of your machines, motor, pump, pulley, drive, rolling element bearing, journal bearing, low speed bearing, gearbox and etc; we can give you fast yet reliable measurement results with full report. You can safe a lots of time and money using our services. Please call 02 971 8086 for more details.

The full report comes with hard copy and full CD-ROM included recorded spectrum file for bearing defect diagnostics.

Training

admin — Wed, 26 Nov 2008 10:23:51 +0000

Training day at Sahaviriya Steel Industries (PUBLIC company) on October 29, 2008 at Prachuabkirikhan province

Nearly 40 engineers and maintenance technicians has participated in training on the use of “Holroyd Instruments for bearing and gearbox condition monitoring”. The training contents cover both theorical and practical aspects of Acoustic Emission technology for maintenance engineers to be able to perform early damage inspection of their rotating equipments.

Maintenance InnoTech 2008

admin — Mon, 24 Nov 2008 16:47:05 +0000

Maintenance InnoTech 2008 is the exhibition all about innovative idea, thinking, practice and instruments for experienced maintenance people. The event has been organised by the group of maintenance engineer in leading company involving in Petrochemical, Paper mill, Particle board, Cement, Steel, Construction and et cetra. We proudly present the Holroyd Instruments products as the leading innovation for experienced condition monitoring engineers.

Opening with pretty MC

Participants and engineers ..

Bearing test rig with MHC Memo to detect faulty bearing…

Our boot and little souvenirs ..

Play game with energy saving airborne sensor to detect air leak..